Blog Archive

Saturday, November 14, 2026

Integrated Geophysical and Geotechnical Site Characterisation for Civil Infrastructure Development in Sekondi-Takoradi, Ghana: Scientific Paper Summary & Review


     This paper details a geotechnical site characterization for its applicability to accommodate heavy structural loads in Sekondi-Takoradi, Ghana. The goal of the investigation, according to the paper’s abstract, is as follows:

“The investigation focused on evaluating the engineering integrity, shear strength, and ultimate bearing capacity of the foundation soils to support heavy structural loads. Additionally, the study aimed to delineate critical subsurface anomalies, weak zones, and adverse geological structures that could compromise structural stability or threaten foundation longevity.”

     Basic site characteristics are shown below.











     The investigation also relied on geophysical surveys, including resistivity imaging and acoustic surveys. The investigation also revealed, “weak lateritic soils often associated with seepage paths that are recognised as near-surface fractures or joints in the areas.” Those areas were found to have negative impacts on the load-bearing capacity of the subsurface.

     The proposed site was designated for the satellite faculty of SRID, Ghana, at Sofokrom (a suburb of Essikado). The site is in a tropical, coastal area with some topographic relief, not too far above sea level, but with hilly areas as well. Some of its characteristics are shown above.

     The geologic setting involves a crystalline basement overlain unconformably by a sedimentary rock sequence consisting of sandstones and shales.

“The sedimentary environment has been interpreted to be of non-marine to coastal marine facies. It was postulated that Paleoweathering in the source area, therefore, is one of the most important processes affecting the composition of sedimentary rocks.”

     The electrical resistivity imaging (ERI) survey involved employing a dipole-dipole array. These are typically used for subsurface thickness, rock structure, groundwater flow and aquifer, groundwater salinity investigations as well as in the oil & gas industry to determine formation water characteristics. The vertical electric sounding (VES) survey was used for subsurface lithologic characterization. VES was done before ERI and was conducted in different features of the terrain, such as hilly areas and depressions, as well as flat areas. A key goal was to identify weak zones where hydrologic seepage was prevalent so they could be avoided.

     Several pits were dug to 1.5 meters, and samples were collected and sent to the lab to determine geotechnical properties such as the Atterberg limits (liquid limit, plastic limit, and plasticity index), particle size distribution, and the direct shear strength. The liquid limit estimates the water content of fine-grained soils. The plastic limit estimates the moisture content of the soil below which it transforms from plastic to a semi-solid state. The plasticity index is “the range of moisture content at which the soil is plastic and is the difference between liquid limit and plastic limit values.” Particle size analysis was performed with standard sieve techniques. The sieved particles were used to determine the specific gravity of the samples. The direct shear test (DST) procedure was done in two test pits of the most common terrain on the site, the hilly terrain and the depressions. It is described below:

“In carrying out this test, a 60 mm × 60 mm cutting box was driven into the undisturbed sample from the trial pits that is forced into the experimental tube to obtain the sample for the test. The extracted sample was carefully put into the shear box to ensure that the ring fitted properly into the shear box apparatus. The gauge for the horizontal movement, vertical movement, and proving ring was adjusted to the zero (2500) mark. The beam jack was adjusted to be in contact with the lever-loading arm and the sample was subjected to the normal loads of 2.1 kg, 4.2 kg, and 8.5 kg. A shear force was then applied under each load and the shear stress was monitored until failure occurred. The sample was unloaded and weighed. The sample was later placed in the oven to dry and its dry weight was recorded. The procedure allows the displacement under shear load, the proving ring reading and settlement dial gauge to be recorded.”

     The derived soil profiles, shown below, showed “stiff, dry brown, loose, and shattered coarse-grained sand silt mixtures” for the top meter with some gravel in a few pits.





     The results of the Atterberg Limits revealed the site was favorable for heavy loads, as described below:

“The relatively low liquid limits and plasticity indices indicate soils with limited volume-change potential, thereby contributing to favourable subgrade performance under anticipated loading conditions. These consistency characteristics were considered together with the particle-size distribution and soil classification in evaluating the engineering suitability of the site.”

     The particle size distribution analysis revealed that the gravelly soils were the best substrate and the silty-sandy soils were rated as a fair substrate, as described below:

“Based on the AASHTO and USCS classification systems, soil samples from trial Pits 1, 2 and 3 are classified as A-2-6 (GC), indicating gravelly soils with clay fines that are generally considered good subgrade materials because of their relatively low plasticity, high gravel content and favourable engineering characteristics. In contrast, trial Pits 4 and 5 are classified as A-2-4 (GM), representing silty gravel soils that are considered fair subgrade materials owing to their comparatively higher sand content and lower cohesion. The engineering assessment of subgrade quality was therefore based on the combined interpretation of the USCS classification, AASHTO classification, particle-size distribution, plasticity characteristics and direct shear strength results rather than on a single engineering parameter.”

     The direct shear test results indicated competent substrate at some pits and less competent substrate at others, suggesting different foundation designs would be required for the less competent areas. A summary of the geotechnical and geophysical investigations is given below.

“In all, the integrated geophysical and geotechnical investigations indicate that the site is generally underlain by competent subsurface materials capable of supporting civil infrastructure. However, localized depressions, fractured zones and areas of elevated moisture content may adversely affect foundation performance. Accordingly, foundation selection should be site-specific, with shallow foundations being suitable in competent areas, while localized ground improvement or deeper foundation systems may be required within weaker zones identified by the integrated investigation.”






     Overall, the site was found to be competent for supporting the heavy loads anticipated in the project, with some foundation design amendments in less competent areas. Composite results of the investigation for each of the five pits are shown in the columns below.



Figure 30. Columnal presentation of the geo-parameters for the lithologic sequence in the study area.





References:

 

Integrated Geophysical and Geotechnical Site Characterisation for Civil Infrastructure Development in Sekondi-Takoradi, Ghana. Asare Asante-Annor, Ernest Nyamekye Addo, Kwaku Raymond Frimpong, and Gbenga Moses Olayanju. Open Journal of Geology. Vol.16 No.7, July 2026. Integrated Geophysical and Geotechnical Site Characterisation for Civil Infrastructure Development in Sekondi-Takoradi, Ghana

No comments:

Post a Comment

     This report explores trends and strategies for dealing with power demand and expanding industrialization. The authors refer to the “...